Inventory #
MC4721
This photo shows a similar circuit breaker to MC4721, after it had undergone remanufacturing by
RESA Power. Actual photos of this FHL26000M4200 Molded Case Breaker in its current condition are shown above.
Catalog #: FHL26000M4200
Type: Molded Case Breaker
Manufacturer: Square D
Voltage: 600 volts
Manual operation
Fixed mounting
Square D FHL26000M4200 Fixed mounted Molded Case Circuit Breaker, Low Voltage, 600 Volts, Manual operation.
RESA Power warranties this rebuilt Square D FHL26000M4200 circuit breaker for one year, including all labor, freight and materials required to return it to operational standards. RESA Power guarantees this breaker will operate to your satisfaction given competent supervision and normal load and usage conditions. Any repairs performed without the express written permission of RESA Power Inc. shall invalidate this warranty. RESA Power shall not be liable to the customer, or to any other person, for consequential damages, lost profits or other kinds of damages arising out of the sale or use of this circuit breaker.
All Square D FHL26000M4200 Molded Case Breakers can be purchased as remanufactured to factory standards (please see FHL26000M4200 factory remanufacturing specification). You can also order your Square D FHL26000M4200 Molded Case Breaker wired to your specified wiring diagrams. We also carry a large stock of replacement parts for the Square D FHL26000M4200 Molded Case Breaker. Call one of our sales consultants today.
At RESA Power, we don’t just rebuild Molded Case Breakers, we remanufacture them. All of our remanufactured circuit breakers conform to NETA and ANSI C37 specifications, and all tolerances are checked to meet or exceed the original manufacturer’s specifications. Here’s how we will remanufacture this Square D FHL26000M4200 for you:
We’ll start with an initial inspection and test of this Molded Case Breaker. We first want to check its mechanical and electrical operation. We’ll then perform a “Ductor” test, a “Megger” test, and several other tests to determine our starting point. (See “Testing Procedures” below for further description.)
During our initial testing, we’ll take note of any wiring, taping, or heat shrinking that shows any signs of deterioration. We’ll also note any springs showing signs of distortion, rust, brittleness, or improper compression. Noted items will be replaced later using equivalent or superior components.
All of our remanufactured circuit breakers are dismantled down to the last moving part:
Now that the circuit breaker has been torn down with all of its components cleaned, refurbished or replaced, it’s time to put it all back together. RESA Power follows a meticulous quality control procedure during reassembly to ensure years of trouble-free operation. Breakers are reassembled to the original factory specification as follows:
Upon completion of reassembly, the now completely remanufactured circuit breaker is retested and certified by a quality control engineer. The rebuilt circuit breaker will be delivered to you with a Job Packet containing an Initial Inspection Report, a Quality Control Checklist, and a Final Test Report. These reports include all pertinent information to ensure that you are receiving a product of the highest quality.
The Digital Low Resistance Ohmmeter (“Ductor”) uses dual spike probes to measure the resistance of the current carrying path of the entire phase. This test includes as much of the path as practical for each pole, ensuring that the entire pole (not just the contacts) has a low resistance.
The insulation of the circuit breaker is tested utilizing a 1000 volt megohmmeter (“Megger”). The breaker is tested in the closed position because of the additional stress placed on the insulators due to spring tension. The insulation is tested between phase-to-phase and phase-to-ground. With the breaker open, the breaker is tested from line-side to load-side of each pole, verifying insulation between the source and the load. The lowest reading of each phase is recorded. RESA Power maintains a standard requirement of a minimum of 500 megohms, ten times NETA minimum requirement.
The high current test is performed using a low voltage (usually less than 12 VAC) high current test set. Each phase or pole is tested for every trip function provided on the trip unit. The test is conducted in the following order to standardize results:
1 Instantaneous is not a time test like the others. Therefore the test uses a short pulse of current and the short time functions are overridden or adjusted out of range of the instantaneous setting.
The control diagram of the circuit breaker is verified against your drawing or the manufacturer’s diagram. The circuit breaker is electrically operated using a variable power supply to check the pick-up voltage of the trip coil, under-voltage coil, and the closing coil. The maximum voltage limit of the close coil is also tested so it will still close and latch.
RESA Power warranties this remanufactured Square D FHL26000M4200 circuit breaker for one year, including all labor, freight and materials required to return it to operational standards. RESA Power guarantees this breaker will operate to your satisfaction given competent supervision and normal load and usage conditions. Any repairs performed without the express written permission of RESA Power Inc. shall invalidate this warranty. RESA Power shall not be liable to the customer, or to any other person, for consequential damages, lost profits or other kinds of damages arising out of the sale or use of this circuit breaker.
Catalog Number | Manufacturer | Type | Frame Current | Voltage |
---|---|---|---|---|
FHL26000M4200 | Square D | Molded Case Breaker | 600 volts | |
FHL26000M4200 | Square D | Molded Case Breaker | 600 volts | |
FHL26000M4200 | Square D | Molded Case Breaker | 600 volts | |
FHL26000M4200 | Square D | Molded Case Breaker | 600 volts | |
FHL26000M4200 | Square D | Molded Case Breaker | 600 volts | |
FHL26000M4200 | Square D | Molded Case Breaker | 600 volts | |
FHL26000M4200 | Square D | Molded Case Breaker | 600 volts | |
FHL26000M4200 | Square D | Molded Case Breaker | 600 volts | |
FHL26000M4200 | Square D | Molded Case Breaker | 600 volts | |
FHL26000M4200 | Square D | Molded Case Breaker | 600 volts | |
KAL26125 | Square D | Molded Case Breaker | 600 volts | |
KAL261525 | Square D | Molded Case Breaker | 600 volts | |
FAL36050 | Square D | Molded Case Breaker | ||
FCL34100 | Square D | Molded Case Breaker | ||
FHP3600311M | Square D | Molded Case Breaker |
Similar Items
to the Square D FHL26000M4200 Circuit Breaker